Design of Road Geometric with AutoCAD® 2D: A Case Wirosari-Ungaran Semarang, Indonesian
DOI:
https://doi.org/10.53866/jimi.v2i5.186Keywords:
Autocad®, Horizontal Alignment, Road Geometric, Vertical AlignmentAbstract
The geometric design of the road Wirosari Semarang to Ungaran road section, which is in the city of Semarang, is one of the infrastructures to provide proper road access with optimal travel time. With the division process, the government must provide proper road access with optimal travel time so that the community mobilization process can run smoothly. The research objective is to plan the geometric shape of the road according to the applicable requirements to provide safety and comfort for road users. The Highway Road Geometric Rule method and visualization using AutoCAD® 2D are used. The results of the geometric planning of the road are obtained with a design speed (Vd) of 60 km/hour, a planned road width of 2 x 3.5 meters, and a road alignment with a horizontal curved Spiral Circle Spiral with a radius of 318 m is formed. Meanwhile, the vertical alignment obtained a concave arch type with a length value (L) of 53.28 m
References
AASTHO. (2018). A Policy on Geometric Design of Highways and Streets. American Association of State Highways and Transportation Officials.
Abduljabbar, R., Dia, H., Liyanage, S., & Bagloee, S. A. (2019). Applications of artificial intelligence in transport:. An overview. Sustainability, 11(1),, 189.
Akgün-Tanbay, N., Campisi, T., Tanbay, T., Tesoriere, G., & Dissanayake, D. (2022). Modelling road user perceptions towards safety, comfort, and chaos at shared space: the via Maqueda case study, italy. Journal of advanced transportation,.
Arsandi, A. S., Ismiyati, I., & Hermawan, F. (2017). Dampak Pertumbuhan Penduduk Terhadap Infrastruktur Di Kota Semarang. Jurnal Karya Teknik Sipil, 6(4),, 01-14.
Asumadu, R., Zhang, J., Zhao, H.-Y., Osei-Wusuansa, H., & Akoto, A.-B. (2019). 3-Dimensional numerical study of wave-induced seabed response around three different types of wind turbine pile foundations. SN Applied Sciences 1(11).
Chakole, H., & J.Wadhai., D. (2022). A Review on The comparison of geometric design using Civil 3D software and manual method. International Journal for Modern Trends in Science and Technology, 115-122.
Costin, A., Adibfar, A., Hu, H., & Chen, S. S. (2018). Building Information Modeling (BIM) for transportation infrastructure–Literature review, applications, challenges, and recommendations. Automation in construction, 94, 257-281.
Ditjen Bina Marga. (2021). Surat Edaran Nomor: 20/SE/Db/2021 tentang Pedoman Desain Geometrik Jalan. In K. P. Marga, Pedoman Desain Geometrik Jalan (p. 24). Jakarta: Kementerian PUPR Ditjen Bina Marga.
Ditjen Bina Marga. (2021). Surat Edaran Nomor: 20/SE/Db/2021 tentang Pedoman Desain Geometrik Jalan. In K. P. Marga, Pedoman Desain Geometrik Jalan (p. 24). Jakarta: Kementerian PUPR Ditjen Bina Marga.
Fan, X., & Huang, Q. (2022). Application of AutoCAD in Auxiliary Design of Highway Bridge Pile Foundation.
Fanning, R., Veith, G., Whitehead, M., & Auman, P. (2021). Guide to road design part 3. In Austroads, Guide to road design part 3 (p. 3). Sydney: Austroads Ltd.
Gaikawad, P., & Ghodmare, S. D. (2020). A Review-Geometric Design of Highway with the Help of Autocad Civil 3D. International Journal for Research in Applied Science and Engineering Technology, 8(5).
Hardati, P., & Setyowati, D. L. (2019). Population Growth in the Upper Garang Watershed Semarang Regency, Central Java Province, Indonesia. IOP Conference Series: Earth and Environmental Science (pp. Vol. 256, No. 1, p. 012032). Semarang: IOP Publishing.
Heinimann, H. R. (2017). Forest road network and transportation engineering–state and perspectives. Croatian Journal of Forest Engineering: Journal for Theory and Application of Forestry Engineering, 38(2),, 188-173.
Ingale, S., Srinivasan, A., & Bairaktarova, D. (2017, August In International Design Engineering Technical Conferences and Computers and Information in Engine). CAD platform independent software for automatic grading of technical drawings. In International Design Engineering Technical Conferences and Computers and Information in Engineering Conference (Vol. 58158, p. V003T04A004). American Society of Mechanical Engineers.
Jimoh, J. A. (2019). Comparative effects of 2D and 3D methods of graphics in autocad on interest of national diploma students in engineering graphics in south-west Nigeria. International Journal of Educational Research, 6(1),, 91-101.
Latif, S. D. (2022). Design of Horizontal and Vertical Alignment for the Centreline of a Federal Highway . I.J Engineering and Manufacturing , 27-42.
Li, C., Ding, L., & Zhong, B. (2019). Highway planning and design in the Qinghai–Tibet Plateau of China: a cost–safety balance perspective. Engineering, 5(2),, 337-349.
Mahanpoor, M., Monajjem, S., & Balali, V. (2021). An optimization model for synchronous road geometric and pavement enhancements. Journal of Traffic and Transportation Engineering (English Edition), 8(3),, 421-438.
Mandal, M., Pawade, P., Sandel, P., & Infrastructure, R. S. (2019). Geometric design of highway using Civil 3D. International Journal of Advance Research, Ideas and Innovations in Technology, 5(3).
O'Flaherty, C. A. (2018). Transport planning and traffic engineering. CRC Press.
Olayode, O. I., Tartibu, L. K., & Okwu, M. O. (2020). Application of Artificial Intelligence in Traffic Control System of Non-autonomous Vehicles at Signalized Road Intersection. Procedia CIRP, 91, 194-200.
Paffumi, E., De Gennaro, M., & Martini, G. (2018). European-wide study on big data for supporting road transport policy. Case Studies on Transport Policy, 6(4), 785-802.
Palilu, A. (2022). Pembangunan Infrastruktur Transportasi Terhadap Produk Domestik Regional Bruto. CV AZKA PUSTAKA.
Pilko, H., Mandžuka, S., & Barić, D. (2017). Urban single-lane roundabouts: A new analytical approach using multi-criteria and simultaneous multi-objective optimization of geometry design, efficiency and safety. Transportation Research Part C: Emerging Technologies, 80,, 257-271.
Putri, E. E., Nanda, M. L., & Aminsyah, M. (2021). Perencanaan Geometrik Jalan Menggunakan Autocad Civil 3D Studi Kasus Jalan Duku–Sicincin (Sta 0+ 000–Sta 2+ 700) Provinsi Sumatera Barat. Jurnal Rekayasa Sipil (JRS-Unand), 17(2),, 140-152.
Rifai, A. I., Hadiwardoyo, S. P., Correia, A. G., & Pereira, P. A. (2016). Genetic Algorithm Applied for Optimization of Pavement Maintenance under Overload Traffic: Case Study Indonesia National Highway. Applied Mechanics and Materials (Vol. 845), pp. 36.
Rifai, A. I., Hadiwardoyo, S. P., Correia, A. G., Pereira, P., & Cortez, P. (2015). The data mining applied for the prediction of highway roughness due to overloaded trucks. International Journal of Technology, 6(5), 751-761.
Rifai, A. I., Hadiwardoyo, S. P., Correia, A. G., Pereira, P., & Cortez, P. (2015). The data mining applied for the prediction of highway roughness due to overloaded trucks. International Journal of Technology, 6(5), 751-761.
Rifai, A. I., Surgiarti, A. Y., Isradi, M., & Mufhidin, A. (2022). Analysis of Road Performance and the impact of Development in Pasar Minggu, Jakarta : Case Study of Jalan Lenteng Agung-Tanjung Barat. ADRI International Journal of Civil Engineering, 68-74.
Shi, Z., Fonseca, J. A., & Schlueter, A. (2017). A review of simulation-based urban form generation and optimization for energy-driven urban design. Building and Environment, 121,, 119-129.
Sil, G., Nama, S., Maji, A., & Maurya, A. K. (2020). Effect of horizontal curve geometry on vehicle speed distribution: a four-lane divided highway study. Transportation letters, 12(10),, 713-722.
Soehodho, S. (2017). Public transportation development and traffic accident prevention in Indonesia. . IATSS research, 76-80.
Soehodho, S. (2017). Public transportation development and traffic accident prevention in Indonesia. IATSS research, 76-80.
Sukalkar, V. G., & Pawar, K. (2022). A Study and Design of Two Lane with Paved Shoulder in Green Filed Corridor, By Using Civil 3D.
Veer, S. P., Gupte, S., & Juremalani, J. (2018). A Review of Literature on Geometric Design of Highway. International Research Journal of Engineering and Technology (IRJET) Volume, 5.
Veer, S. P., Gupte, S., & Juremalani, J. (2018). A Review of Literature on Geometric Design of Highway. International Research Journal of Engineering and Technology (IRJET) Volume, 5., 1.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2022 Dimas Sukma Adiputra, Andri Irfan Rifai, Surya Kencana Bhakti
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
